2008 July RFA Experiment Georgetown - Revision history

Hliu at 14:29, 6 August 2008

2008-08-06T14:29:21Z

Hliu at 18:11, 25 July 2008

2008-07-25T18:11:36Z

ZivYaniv at 20:31, 24 July 2008

2008-07-24T20:31:09Z

ZivYaniv: /* Participants */

2008-07-24T20:08:38Z

Participants

Hliu at 02:39, 24 July 2008

2008-07-24T02:39:25Z

Hliu: /* Agenda */

2008-07-24T02:38:08Z

Agenda

Hliu: /* Agenda */

2008-07-24T02:36:08Z

Agenda

Hliu: /* Schedule */

2008-07-24T02:31:26Z

Schedule

Hliu: New page: Date: July 30 - August 1, 2008 Location: Imaging Science and Information Systems (ISIS) Center, Department of Radiology, Georgetown University Medical Center, 2115 Wisconsin Avenue, Suite...

2008-07-24T02:26:22Z

New page: Date: July 30 - August 1, 2008 Location: Imaging Science and Information Systems (ISIS) Center, Department of Radiology, Georgetown University Medical Center, 2115 Wisconsin Avenue, Suite...

New page

Date: July 30 - August 1, 2008

Location: Imaging Science and Information Systems (ISIS) Center, Department of Radiology, Georgetown University Medical Center, 2115 Wisconsin Avenue, Suite 603, Washington, DC, 20007

=Participants=
*Kevin Cleary
*Ziv Yaniv
*Filip Banovac
*Noby Hata
*Haiying Liu

=Schedule=
Wednesday (7/30): Phantom experiment will start around 5pm if all goes well.
Other days: Work on the IGSTK/OpenIGTLink/Slicer interface for sending the transforms so that a working example may be built that sends transforms from IGSTK to Slicer and that this program is configurable, supporting all of the IGSTK trackers.

=Agenda=

=Results=

@@ Line 38: / Line 38: @@
 #Fil navigates to the prescribed locations according to plan.
 #Optional: After each needle positioning, stop George's breathing and acquire a CBCT scan with needle in place. After the fact register the regions of interest to the planning CBCT and compute the distances between the planned needle location and the actual location.
 =Results=

@@ Line 18: / Line 18: @@
 *Do RFA phantom experiment on 07/30 (will start around 5pm if all goes well).
 *Work on the IGSTK/OpenIGTLink/Slicer interface for sending the transforms so that a working example may be built that sends transforms from IGSTK to Slicer and that this program is configurable, supporting all of the IGSTK trackers.
 *Hammer out the details of how to communicate a segmentation performed in slicer to the path planning component and then upload the plan back to Slicer.
 *It would be nice to create stubs that allow us to go through the whole workflow in Slicer so that we have an initial module into which the actual content can be added later.
@@ Line 40: / Line 39: @@
 #Optional: After each needle positioning, stop George's breathing and acquire a CBCT scan with needle in place. After the fact register the regions of interest to the planning CBCT and compute the distances between the planned needle location and the actual location.
 =Results=

@@ Line 14: / Line 14: @@
 *Filip Banovac (GU)
 *Ziv Yaniv (GU)
 =Agenda=
-*Do RFA phantom experiment on 07/30.
+*Do RFA phantom experiment on 07/30 (will start around 5pm if all goes well).
 *Work on the IGSTK/OpenIGTLink/Slicer interface for sending the transforms so that a working example may be built that sends transforms from IGSTK to Slicer and that this program is configurable, supporting all of the IGSTK trackers.
 **Patient to image registration (using Landmarks) in Slicer?
 *Hammer out the details of how to communicate a segmentation performed in slicer to the path planning component and then upload the plan back to Slicer.
 *It would be nice to create stubs that allow us to go through the whole workflow in Slicer so that we have an initial module into which the actual content can be added later.
 =Results=

@@ Line 16: / Line 16: @@
 *Do RFA phantom experiment on 07/30.
 *Work on the IGSTK/OpenIGTLink/Slicer interface for sending the transforms so that a working example may be built that sends transforms from IGSTK to Slicer and that this program is configurable, supporting all of the IGSTK trackers.
 *Hammer out the details of how to communicate a segmentation performed in slicer to the path planning component and then upload the plan back to Slicer.
 *It would be nice to create stubs that allow us to go through the whole workflow in Slicer so that we have an initial module into which the actual content can be added later.
 =Results=

← Older revision		Revision as of 02:36, 24 July 2008
Line 14:		Line 14:

	=Agenda=		=Agenda=
		+	*Do RFA phantom experiment on 07/30.
		+	*Work on the IGSTK/OpenIGTLink/Slicer interface for sending the transforms so that a working example may be built that sends transforms from IGSTK to Slicer and that this program is configurable, supporting all of the IGSTK trackers.
		+	*Hammer out the details of how to communicate a segmentation performed in slicer to the path planning component and then upload the plan back to Slicer.
		+	*It would be nice to create stubs that allow us to go through the whole workflow in Slicer so that we have an initial module into which the actual content can be added later.

	=Results=		=Results=

@@ Line 4: / Line 4: @@
 =Participants=
-*Kevin Cleary
+*Noby Hata (BWH)
-*Ziv Yaniv
+*Haiying Liu (BWH)
-*Filip Banovac
+*Enrique Campos-Nanez (GWU)
-*Noby Hata
+*Teo Popa (GU)
-*Haiying Liu
+*Patrick Cheng (GU)
 =Schedule=

@@ Line 1: / Line 1: @@
-Date: July 30 - August 1, 2008
+'''Date''': July 30 - August 1, 2008
-Location: Imaging Science and Information Systems (ISIS) Center, Department of Radiology, Georgetown University Medical Center, 2115 Wisconsin Avenue, Suite 603, Washington, DC, 20007
+'''Location''': Imaging Science and Information Systems (ISIS) Center, Department of Radiology, Georgetown University Medical Center, 2115 Wisconsin Avenue, Suite 603, Washington, DC, 20007
 =Participants=