IGT:ToolKit/Build-Tracker-Simulator - Revision history

Hliu: /* Linux / Mac OS X */

2009-04-08T21:06:52Z

Linux / Mac OS X

Noby at 19:07, 27 October 2008

2008-10-27T19:07:09Z

Dpace at 22:24, 10 October 2008

2008-10-10T22:24:51Z

Dpace at 12:54, 4 June 2008

2008-06-04T12:54:15Z

Dpace: New page: Back to IGT:ToolKit ===Notes before you begin=== * Slicer3 is assumed to have been built on your computer in the directory '''igt-tutorial''' * CMake 2.6 is absolutely re...

2008-06-04T02:37:23Z

New page: Back to IGT:ToolKit ===Notes before you begin=== * Slicer3 is assumed to have been built on your computer in the directory '''igt-tutorial''' * CMake 2.6 is absolutely re...

New page

Back to [[IGT:ToolKit|IGT:ToolKit]]

===Notes before you begin===
* Slicer3 is assumed to have been built on your computer in the directory '''igt-tutorial'''
* CMake 2.6 is absolutely required. If you don't have it installed, you can use the version of ccmake found in igt-tutorial/Slicer3-lib/CMake-build/bin (it will be CMake 2.6)

===Instructions===

First, get the tracker simulator source code from the repository:
$ cd igt-tutorial
$ svn co http://www.na-mic.org/svn/NAMICSandBox/trunk/BRPTools/ScannerIO ScannerIO

Configure using CMake 2.6: You should not need to change any settings - just press the 'c' key followed by the 'g' key to generate the makefiles.
$ cd ScannerIO
$ ccmake .

If the previous command has completed without error, you can start building:
$ make

Upon completion, you should find the '''TrackerSim''' executable file at ScannerIO/bin

@@ Line 13: / Line 13: @@
    $ ccmake ../OpenIGTLink
-Then CMake configuration screen shows up on your terminal. Normally, you don't need to change any options. Just press the 'c' key (configure) followed by the 'g' key (generate). and quit the configuration screen. Now you are ready to build the software.
+Then CMake configuration screen shows up on your terminal. Normally, you don't need to change any options except making sure BUILD_EXAMPLES is ON. Just press the 'c' key (configure) followed by the 'g' key (generate). and quit the configuration screen. Now you are ready to build the software.
    $ make

@@ Line 1: / Line 1: @@
 Back to [[IGT:ToolKit|IGT:ToolKit]]
-===Notes before you begin===
+== Linux / Mac OS X ==
-===Instructions===
+First obtain the source code from the repository. Open the terminal and run:
-First, get the tracker simulator source code from the repository:
+   $ svn co http://svn.na-mic.org/NAMICSandBox/trunk/OpenIGTLink OpenIGTLink
-Configure using CMake 2.6:  You should not need to change any settings - just press the 'c' key followed by the 'g' key to generate the makefiles.
+Then configure using CMake. The library requires CMake version higher than 2.4.
-''' Windows '''
+Then CMake configuration screen shows up on your terminal. Normally, you don't need to change any options. Just press the 'c' key (configure) followed by the 'g' key (generate). and quit the configuration screen. Now you are ready to build the software.
-* Open ScannerIO.sln in the ScannerIO folder
-* Build -> Build Solution
+  $ make
-* Copy ScannerIOLib.dll from the ScannerIO/Debug folder to the ScannerIO/bin/Debug folder
-* Make sure the Windows firewall is '''off'''
+You may install the library into your disk (optional). The default target directory is /usr/local, but you can configure it from the CMake configuration screen. To install the files, run
-Upon completion, you will find TrackerSim.exe in ScannerIO/bin/Debug
 Upon completion, you should find the '''TrackerSim''' executable file in ScannerIO/bin

← Older revision		Revision as of 12:54, 4 June 2008
Line 1:		Line 1:
	Back to [[IGT:ToolKit\|IGT:ToolKit]]		Back to [[IGT:ToolKit\|IGT:ToolKit]]
−

	===Notes before you begin===		===Notes before you begin===

@@ Line 12: / Line 12: @@
 Configure using CMake 2.6:  You should not need to change any settings - just press the 'c' key followed by the 'g' key to generate the makefiles.
   $ cd ScannerIO
   $ ccmake .
@@ Line 18: / Line 27: @@
    $ make
-Upon completion, you should find the '''TrackerSim''' executable file at ScannerIO/bin
+Upon completion, you should find the '''TrackerSim''' executable file in ScannerIO/bin